4. August 2010 by Sean.

Well, it took a year, but someone has finally shown an interest in the SPOT GPS tracking device hack that we built.  I’m proud.  As promised, here are the files: 

SPOT Hack files

There is a PDF for the schematic but the board design will need to be brought up in Kicad.

Everything supplied is as-is.  No guarantees, no responsibility if it burns your house down, no apologies for missing documentation.

Posted in Uncategorized | 5 Comments »

20. July 2010 by Sean.

Ok, we’ve got all the pieces talking to one another and a nice stable boat.  Tomorrow is our speed test so I thought we should wet test it first. The motor speed took a bit of adjusting.

For those of you who use Google Earth, you can see the Elk Lake Course
here.

Posted in Uncategorized | 17 Comments »

3. June 2010 by gmoney.

2 pieces of 3/16″ (5mm) acrylic getting mounted on SolarCrawler^® -  22″ x 13″ ’semi-circle’ over the bow, and 22″ x 18″ piece over the stern.  I’m concerned about the weight of all this acrylic (feels like maybe 3-4 pounds) but I wouldn’t want to risk anything thinner in terms of durability.

8 of the Pitsco solar panels will be mounted on the stern portion of the acrylic.  the 9th will be on the bow, this still leaves enough space for the GPS and SPOT device to have a clear view of the sky.  In fact I may try and sneak a few more solar panels around the bow, I saw some decent 3v 60mm square panels for sale in the latest issue of “Nuts and Volts” from allelectronics.com that I think I’ll order up — every little bit of power helps!!

Posted in Uncategorized | 18 Comments »

27. May 2010 by gmoney.

After a winter of procrastination, I pulled out the fiberglass supplies last week.  My goal was to apply the second and final layer to the bow.  Due to a lack of patience and daylight I decided to apply the whole thing with a single piece of fiberglass (I was using 2 before) - it turned out great!

Posted in Fiberglass construction, Uncategorized | 18 Comments »

26. April 2010 by Sean.

Now that the sun is out again, it’s time to ramp up the solarboat project.  Greg and I have set some aggressive targets for building.  Although no postings lately, we have been indirectly working on the boat.  Here’s what’s happened over the past few months:

1. Because GPS is CPU intensive and critical to what we’re doing, we encapsulated the GPS navigation onto a separate board.  This handles everything including reading the NMEA stream and calculating the destination bearing and distance to destination.  It’s got an I2C interface and was recently used in the Sparkfun Autonomous Vehicle Competition for our modified RC car.  Unfortunately we did not win, but it wasn’t because of the GPS navigation.  What’s that?  Can you buy one of these?  Well in fact, yes.  We had a bunch made and you buy them here.
2. Due to an unfortunate accident (I would like to say it’s not my fault, but you can judge for yourself (click)) I lost my laptop in the name of GPS research.
3. Most recently, we’ve taken the brushless motor driver that we built from scratch (see below) and have built an I2C interface to it.  Each modified CD ROM motor will have its own controller and a distinct I2C address.  We will be able to give each motor its own address and RPM feedback.  That will let us implement the redundancy that we want (4 motors in case 1 or 2 go belly up).

Posted in Uncategorized | 3 Comments »

6. September 2009 by Sean.

After trying many combinations of commercial brushed and brushless motors, we resorted to winding our own. I didn’t think this was feasible but came across this site: http://www.strongrcmotors.com/ Don, the proprietor, was very helpful and gave us some tips on winding a motor around our needs (as you’ve read many times, 200 mA draw, as much thrust as possible).

The kits are made from CDROM motors and customized parts. Usually, these are used for home-built RC planes so we had to experiment quite a bit using thin wire and lots of winds. It was then that we found out that commercial brushless motor controllers wouldn’t work at low current draw so we built our own.

The magic formula is (and this is the result of easily a month of investigation so please at least pretend like you’re excited) 100 turns of 38 gauge magnet wire. That’s specific and tuned to our purpose: high pitch, 2 bladed, 2 inch prop underwater running at 100% duty cycle. 38 gauge wire is about twice as thick as human hair (Science Nerd measured it).

I would post a picture, it would look a lot like any other failed attempt (blog Aug 6th entry).

Posted in Uncategorized | 8 Comments »

3. September 2009 by gmoney.

I don’t know what my next project will be after the solar boat, but I do know it won’t involve fiberglass

Posted in Uncategorized | 3 Comments »

11. August 2009 by Sean.

Course #1 (Elk Lake, Victoria, BC) was successfully completed tonight.  It took a while (exactly 10 min) but all points were hit and the motors shut down when it reached the last point.

Posted in Uncategorized | 18 Comments »

6. August 2009 by gmoney.

Posted in Uncategorized | 1 Comment »

6. August 2009 by gmoney.

Last week’s geek-nite - installing motor shafts and braces in proto boat2.  Still not sure if we’re going with the low power draw brushed motors or custom built brushless motors.   Brushless motors may require too much juice to operate at a reasonably efficient level.

Drilling holes in shafts for lube:

Shafts installed:

Preparing the motor brace:

Posted in Uncategorized | 3 Comments »